Home > Shop by Size >

VTASL59 59" Heated Air Jetted Single Slipper Tub with Drain and Concealed Blower
VTASL59 59in Hot Air Massage Single Slipper Tub
 
Alternative Views:


There is a deck area on this tub and it can be used with many deck mounted faucets and all wall mounted and freestanding faucets.
If you purchase a faucet from us, we will drill the deck holes to suit the faucet.
Includes Victorian drain with overflow
Ultra-Quiet heated single speed air blower located inside pedestal base
Powerful 600w heater on the blower to increase air bubble temperature
When the bubbles enter the water, even though they are warm, they will feel slightly cool to the skin
Anti-back flow and Hartford Loop safety (outside back of tub)
Requires a dedicated standard 15amp - 110v GFCI
18 individual white air injectors in the floor
Three foot of cable from the tub to the wall
Slip resistant floor

MA Code Accepted

Specification Sheet
Your Price: $1,798.00

Please Note: This tub is made to order and may take up to 2-3 weeks for preperation.


Availability:: Ships approximately May 15th
Product Code: VTASL59


SS Overflow and Drain Finish*:
Chrome
Brushed Nickel
Polished Nickel
Oil Rubbed Bronze
Don't supply a drain [Subtract -$35.00]

Chromotherapy*:
Don't add chromotherapy (no extra)
Add chromotherapy [Add $185.00]

Ozone Sanitizing*:
Don't add ozone sanitizing
Add Ozone Sanitizing [Add $175.00]

Tub Exterior Finish*:
Leave tub as high gloss white finish
Paint tub exterior to match solid color details I will send [Add $285.00]
Aged Chrome [Add $499.00]
Aged Copper Leaf [Add $499.00]
Aged Umber Gold Leaf [Add $499.00]
Aged Umber Silver Leaf [Add $499.00]
Eggshell Black [Add $285.00]

Description
 
VTASL59 59" Heated Air Jetted Single Slipper Tub with Drain and Concealed Blower
Ready to plug in to a 15 amp 110 v GFCI
Photo here shows 67" version of the tub, proportions may change a little on different length tubs

Soothe away the aches of the day in a luxurious heated air massage bathtub. We offer single speed on/off control. All of our individual flat face air injectors are placed on the bottom of the tub to massage calves and thighs. We use a powerful 600w heater in our hot air blower to increase the ambient temperature 15 to 20 degrees within a period of around 2 minutes, so switching the air jetting on before entering the tub can be a good idea.While the air is heated, it can still feel slightly cool when the bubbles meets the skin, it will not feel hotter than the water in the tub.
Installation on this tub is very simple, everything needed is part of the tub. Simply connect the regular 3-pin plug to a 110v-15 amp GFCI and you're ready to go. The blower is inside the pedestal. In the unlikely event of a blower failure, replacing it is also very simple, just disconnect the electric and tub from the drain, turn it over and replace the blower, about a 30 minute job.
On the back or wall side of these pedestal jetted tubs, to comply with UL regulations and for operating safety, we are required to install a Hartford loop. Since this is at the back or side of the tub, it will not be visible if the tub is placed against a wall. If the tub is being placed in a central position, this is a feature of which you should be aware.
To maintain hygiene in the air pipes, every time you take a bath and drain the water, engage the blower for about 15 seconds to purge all residual water in the lines. Every three months, we recommend that you fill the tub about two inches over the highest jet with luke warm water and add a half cup of bleach. Engage the blower and let run for two minutes. Empty and repeat this step with clean water and purge the lines when the tub is empty.